無錫糖果廠地坪價格是多少400-0709-910(請撥打400-0709-910電話，永堅地坪公司)
耐磨地坪漆施工中,最常見涂膜干燥方式是自然干燥,也可以成為常溫干燥.但是這種干燥方法時間較長,而且受自然影響較嚴重.而且在環氧地坪漆的涂裝后,涂膜越厚,完全干燥的時間就越長.
在涂膜的自然干燥過程中要注意以下幾點:
1、環境的濕度對干燥的速度和涂膜的質量會有很大的影響.濕度高的情況下,可能會早場涂膜泛白.還可能會造成涂膜回粘,因此,**是濕度要小于75%.在通風的環境下,涂膜更容易干燥.但是風速不宜太大,否則會影響涂膜的質量.
2、氣溫太低或者是太高都會影響成膜的質量,所以應選擇適宜的天氣施工.光照對常溫干燥也有很大的幫助,紫外線的光對聚合有明顯作用,但也可能對涂膜造成傷害,要把握好度很重要.
把握好涂膜的干燥在整個停車場由于需要規劃停車位置，同時還要安裝相應的防護裝置，因此需要提供各種不同顏色，不同規格的停車場地板漆來做好相應的規劃，也因此而增加了施工的難度，在整個停車場的施工，每一個部分都需要精心的設計和規劃，從而更加**的給予駕駛者一定的指示，既然停車場需要規劃不同的顏色，那么我們?cè)撊绾稳ピO(shè)計才能夠更好的利用整個停車場呢？小編擁有如下建議。
1、停車區對于平整地面,可采用0.5mm普通環氧地坪，而平整度及表面強度較差的地面，可以采用1-3 mm環氧砂漿地坪，**要求可采用2-3mm環氧自流平地坪；顏色可設計成灰色。
2、車行通道由于車行頻繁，相對于停車區，設計要加強，可采用1-3 mm環氧砂漿地坪或2-3mm環氧自流平地坪，顏色通常為綠色，車行通道寬度根據現場情況設置，通常雙向行車道不宜低于6米，單向行車道不宜低于3米，人行通道為1.5-2米，通道兩側劃中黃色標志線，線寬8-12mm。
3、車行標志通道內可采用黃色或白色標志漆（可采用夜發花地坪漆）畫箭頭進行標明車行方向及指向各停車區，如A停車區、B停車區及C停車區等。
4、停車位設置按停車場地面區域結構設置停車位，小轎車通常可設計為2.5-3.0米X5-6米，停車位采用黃色或白色標志線畫出，標線寬8-12mm。
5、柱面處理為增加停車場柱面的醒目性，避免因倒車碰到柱子，柱子下端1.0-1.2米以下可采用黃色和白色相間斜紋斑馬線進行標明。
6、車輛出入口坡道無震動防滑地坪，車輛出入品必須具有防滑**噪音作用，有的停車場土建施工時已考慮到了，將之施工成波紋形不平的地面，這種情況下只需一部分涂車行通道顏色，一部分涂另一顏色，兩種顏色相間就可以了。如果土建時未設計考慮防滑要求，在地坪施工明此處應采用AKF防滑地坪，而且防滑骨料顆徑應較大，通常直徑不低于2mm，視坡道傾斜度而選擇合適顆徑的防滑骨料。
7、墻裙處理墻裙涂以和墻面及地面不一樣的顏色，可在車行時起到提醒的作用。但不宜過高，一般0.2-0.7米即可。采用深綠色和Wear-resistant floor paint construction, coating drying method is the most common natural drying, can also be dried at room temperature. However, this method of drying a long time, but also by the impact of a more serious nature. And in epoxy floor paint coating After coating thicker, longer time to dry completely.
In the natural drying process of the coating should note the following:
1, the humidity will be on the quality of the dried coating speed and great influence. Under high humidity conditions, may be early field film whitening is also likely to cause the coating stick back, therefore, it is best humidity to less than 75% in a ventilated environment, the film is more prone to dryness but wind speed should not be too large, otherwise it will affect the quality of the coating.
2, the temperature is too low or too high will affect the quality of a film, it should choose the appropriate weather construction. Light on drying at room temperature is also a great help, ultraviolet light polymerization plays a significant role, but may also result in the film injury, it is important to grasp the degree.
A good grasp of the coating was dried in entire parking lot due to the need to plan for the parking position, but also install the appropriate protective equipment, and therefore need to provide a variety of different colors, different sizes of parking lot floor paint to make the appropriate planning, has thus increase the difficulty of construction, the construction of the entire parking lot, each part requires careful design and planning, and thus more effective to give some indication of the driver, since the parking lot need to plan a different color, then how do we go design to be able to make better use of the entire car park it? Xiao Bian has the following recommendations.
1, the parking area for a flat on the ground, can be 0.5mm ordinary epoxy, and poor surface smoothness and strength on the ground, can be used 1-3 mm epoxy mortar floor, epoxy-level requirements can be 2-3mm self-leveling floor; color can be designed into gray.
2, the companies channel dealers frequently due respect to the parking area, designed to strengthen, may be 1-3 mm epoxy mortar floor or 2-3mm self-leveling epoxy floor, color is usually green, dealers channel width according to scene setting, usually not less than two-way lane 6 meters, one-way carriageway not less than 3 meters, pedestrian passage of 1.5-2 meters on either side draw yellow flag line, width 8-12mm.
3, inside the garage label channel may be yellow or white sign paint (floor paint can blur night) Draw arrows to indicate the direction and point to individual dealers parking areas, such as parking areas A, B and C parking area parking area, etc. .
4, parking set up regional structures set up by parking ground parking spaces, cars can be designed generally 2.5-3.0 meters X5-6 meters, parking signs use yellow or white line drawing, standard width 8-12mm.
5, cylindrical handle to increase the conspicuity parking cylinder to avoid reversing across pillars, 1.0-1.2 meters below the lower end may be yellow and white twill zebra crossing be identified.
6, vehicle entrance ramp non-slip floor no vibration, vehicle access product must have non-slip effect eliminate noise, parking and some civil construction has been incorporated into the construction of a corrugated uneven ground, just a part of this case channel color coated dealers, part painted another color, two colors and white on it. If design considerations do not slip when the civil claim, on the ground floor construction should be clear here AKF slip floor and non-slip aggregate particle diameter should be larger, typically a diameter of not less than 2mm, depending on the inclination of the ramp and choose a suitable particle diameter non-slip aggregate.
7, processing dado dado and wall and floor coated with different colors, can play a role in reminding dealers. But not too high, generally 0.2 to 0.7 meters away. With deep green and pale gray and white were signs.
資訊來源：<聯系電話:400-0709-910>
|
您當前的位置: 首頁 > 行業資訊
